Build and preview

The starter pack provides a Makefile that defines make commands to build and view the documentation.

This guide describes how to set up your environment and use these commands to build and preview the documentation locally.

For more advanced information, including how to embed your docs build with your project build, see:

Install prerequisite software

The documentation framework that the starter pack uses bundles most prerequisites in a Python virtual environment, so you don’t need to worry about installing them. There are only a few packages that you need to install on your host system.

Before you start, make sure that you have make, python3, python3-venv, and python3-pip on your system:

sudo apt update
sudo apt install make python3 python3-venv python3-pip

Python environment

The Python prerequisites from the docs/requirements.txt file are automatically installed when you build the documentation.

If you want to install them manually, you can run the following command from within your documentation folder:

make install

This command creates a virtual environment (.sphinx/venv/) and installs dependency software within it.

If you want to remove the installed Python packages (for example, to enforce a re-installation), run the following command from within your documentation folder:

make clean

Note

  • By default, the starter pack uses the latest compatible version of all tools and does not pin its requirements. This might change temporarily if there is an incompatibility with a new tool version. There is therefore no need to use a tool like Renovate to automatically update the requirements.

  • If you encounter the error locale.Error: unsupported locale setting when activating the Python virtual environment, include the environment variable in the command and try again: LC_ALL=en_US.UTF-8 make run

Important

Run these commands from within your documentation folder.

Build the documentation

To build the documentation, run the following command:

make html

This command installs the required tools and renders the output to the _build/ folder in your documentation folder.

Important

When you run make html again, it updates the documentation for changed files only.

This speeds up the build, but it can cause you to miss warnings or errors that were displayed before. To force a clean build, see Run a clean build.

Make sure that the documentation builds without any warnings (warnings are treated as errors).

Run a clean build

To delete all existing output files and build all files again, run the following command:

make clean-doc html

To delete both the existing output files and the Python environment and build the full documentation again, run the following command:

make clean html

View the documentation

To view the documentation output, run the following command:

make serve

This command builds the documentation and serves it on http://127.0.0.1:8000/.

Live view

Instead of building the documentation for each change and then serving it, you can run a live preview of the documentation:

make run

This command builds the documentation and serves it on http://127.0.0.1:8000/. When you change a documentation file and save it, the documentation will be automatically rebuilt and refreshed in the browser.

Important

The run target is very convenient while working on documentation updates.

However, it is quite error-prone because it displays warnings or errors only when they occur. If you save other files later, you might miss these messages.

Therefore, you should always Run a clean build before finalising your changes.

Build a PDF

Build a PDF locally with the following command:

make pdf

PDF generation requires specific software packages. If these files are not found, a prompt will be presented and the generation will stop.

Required software packages include:

  • dvipng

  • fonts-freefont-otf

  • latexmk

  • plantuml

  • tex-gyre

  • texlive-font-utils

  • texlive-fonts-recommended

  • texlive-lang-cjk

  • texlive-latex-extra

  • texlive-latex-recommended

  • texlive-xetex

  • xindy

On Linux, required packages can be installed with:

make pdf-prep-force

Note

When generating a PDF, the index page is considered a ‘foreword’ and will not be labelled with a chapter.

Important

When generating a PDF, it is important to not use additional headings before a toctree. Documents referenced by the toctree will be nested under any provided headings.

A rubric directive can be combined with the h2 class to provide a heading-styled rubric in the HTML output. See the default index.rst for an example. Rubric-based headings aren’t included as entries in the table of contents or the navigation sidebar.